LMS 202 CR CONTAINER READY PORTABLE TOWER

LMS 202 CR

LMS = Landa Mobile Systems
CR = Container Ready
202′ = height in feet

  • 202’ CR MODEL 
  • ALL SECTIONS ASTM A500-07, A53-12, GRADE B, CARBON STEEL,  Lifetime Warranty
  • TRAILER INTEGRATED TOWER TILT BASE ASSEMBLY SUPPORTS OUR COMPLETE LINE OF LATTICE TOWERS.  Lifetime Warranty
  • 3 SECTOR ANTENNA MOUNT / CUSTOM MOUNT DESIGNS AVAILABLE
  • DUAL TORSION ROD DESIGN WITH MULTIPLE STIFFENER PLATES
  • HOT DIPPED GALVANIZED FINISH EN ISO 1461/ASTM A123/CSA G164 FOR ALL WEATHER
  • 900:1 WORM DRIVE ALLOWING TOWER TO BE SAFELY DEPLOYED AT ANY HEIGHT 
  • EQUIPPED WITH BACKUP POWERLESS KEY OPERATION ALLOWING TOWER TO BE RAISED OR LOWERED WITH A CORDLESS DRILL
  • THEFT PROOF CABLE STORAGE REEL, OPTIONAL ELECTRIC, MULTIPLE REELS, SPLIT REELS AND HANDLES
  • 8 EA CABLE GUIDE RINGS
  • WEATHERPROOF (LOCKING) CONTROL PANEL
  • 2 EA SWITCHES FOR TOTAL DEPLOYMENT CONTROLS 
  • 1 MINUTE FROM HORIZONTAL TO VERTICAL WITH LOAD
  • 22 MIN TO FULL ERECTION
  • HYDRAULIC SYSTEMS TILTING WITH HEAD LOAD
  • 2000 TILT PAY LOAD
  • 2000Lb PAYLOAD CERTIFIED
  • 2000Lb VERTICAL LIFT ABILITY
  • OPTIONAL 4,000LB LIFTING CAPABILITY
  • HEAVY DUTY UPPER AND LOWER LIMIT SWITCHES
  • 110VAC 60HZ / OPTIONAL 240VAC 2000 LB TILT CAPACITY 
  • PATENTED DERLIN MAST GUIDE BLOCKS
  • VERTICAL LIFT ABILITY TESTED TO 2000LBS
  • HIGH STRENGTH AIRCRAFT QUALITY LIFTING CABLES
  • REDUNDANT TOWER RETRACTION CABLES MARINATED IN LPS3
  • 4″, 5″AND 6″ STEEL CUSTOM BEARING FITTED LANDA PULLEYS
  • ALL LIFT CABLES 3/8″ MARINATED IN LPS3
  • ALL ECO COATED GRADE 9 BOLTS  
  • MOTOR DRIVE UNITS  Main drive motor is wash-down direct drive worm gear extreme environment w/moisture drain.  All units are designed to withstand the most severe  -120 / 160 degrees Fahrenheit conditions without failure.
  • STEEL SAFETY END CAP AND LIFTING DRUM SAFETY COVERS
  • LMS NEVER FAIL KEY SYSTEM INCLUDED utilizing a key and a cordless drill both tilt and erection systems backed up in case of a remote or no power. The Lattice Towers are 100% Redundant backed up as a true emergency unit in the field, and you will not be let down when its critical. Lifetime Warranty

LMS OPTIONS

DEPOLYED UNITS

TOWER TRAILER

  • TOWER TRAILER Structural Outrigger and Tower tilt assembly have a Lifetime Warranty (not including standard wear items i.e. electrical, brakes, tires, bearings, jacks, rubber and plastics)
  • DIAMOND PLATE 11 GAUGE DECK
  • DECKS WATER-FALL SIDES ADD 400% TO STRENGTH VS.FLAT STEEL WELDED TO RAIL  Lifetime Warranty
  • ELECTRICAL COMPONENTS BONDED TO FRAME FOR SYSTEM GROUNDING
  • INTEGRATED TOWER BASE TILT SYSTEM CONSTRUCTED WITH 4”X4”X1/4” STRUCTURAL TUBING FOR EXTRA STRENGTH 
  • ALL STEEL CONSTRUCTION 10” WIDE BEAM CONSTRUCTION, NO ALUMINUM
  • 1/4 ” LINE X SPRAYED ON FULL DECK AND FRONT OF TRAILER FOR ANTI SLIP
  • ANTI-THEFT REMOVABLE TONGUE
  • 11 HOLE ADJUSTABLE COUPLER CHANNEL W/REMOVABLE 2 5/16″ BALL HITCH, PINTLE
  • 7 PIN RV-TYPE CONNECTOR
  • 12,000 LB SIDE PULL SPRING LOADED TONGUE JACK 
  • EMERGENCY TRAILER BREAKAWAY DEVICE
  • 2 EA TWO HOLE 1/0 GROUND LUGS
  • 2 EA HEAVY DUTY SAFETY CHAINS
  • 1 EA BUILT IN GROUND ROD STORAGE
  • 4 EA TUBE GROUND ROD ATTACH POINT HOLDERS WELDED TO OUTRIGGERS
  • 6 EA TELESCOPIC CRANE STYLE NEEDLE BEARING OUTRIGGERS
  • 6 EA ADJUSTABLE 12,000 LB LOCKING OUTRIGGER JACKS W/ PADLOCK PROVIDED
  • 6 EA GALVANIZED 2′ X 2′ OUTRIGGER JACK PADS
  • 6 EA HEAVY DUTY OUTRIGGER SAFETY CHAINS
  • 2 EA REAR 12,000Lb LEVELING JACKS
  • 2 EA MID-TRAILER 12,000Lb LEVELING JACKS
  • 1 EA 12,000Lb LIFTING JACK FOR PINTLE OR STANDARD HITCH TRAILER
  • 4 EA BUBBLE TYPE TRAILER LEVEL GUIDES
  • 3 EA 8,000LB TORSION AXLES, OIL BATH, EACH ELECTRIC BRAKES
  • FULL SIZE SPARE TIRE UNDER DECK
  • ALL WEATHER PADLOCKS AND HIDE-A-KEY
  • 7 EA 16 PLY 215-75-17.5 RADIAL TIRES
  • 7 EA 17.50 POWDER COATED SOLID STEEL WHEELS  Lifetime Warranty
  • 6 SETS WHEEL SETS LOOSE NUT INDICATORS
  • 1 EA TRAILER STEP AND HAND RAIL 
  • DOT AND TRANSPORT CANADA LED LIGHTING PACKAGE AND REFLECTIVE TAPE
  • 36” STEEL LOCKING ALUMINUM POWDER COATED BLACK DIAMOND PLATE TOOL BOX WITH ANTI-THEFT DEVICE
  • FLASHING EMERGENCY LIGHTS
  • MAXIMUM ANGLE OF TERRAIN IN DEGREES FOR SAFE TRAILER DEPLOYMENT UP TO 7 DEGREES SIDE TO SIDE, 3.5 DEGREES FRONT TO BACK WITHOUT ADDITIONAL BLOCKING
  • GUY RADIUS AND ADDITIONAL ANCHOR DESIGN DEPENDENT ON LOADING AND WINDS TO BE DETERMINED BY ENGINEERING
  • 12 POSITION GUY KIT
  • UNGUYED FOOT PRINT SAME AS OUTRIGGER FOOT PRINT
  • EQUIPPED WITH LIFTING HOOKS IN ALL FOUR CORNERS FOR HELICOPTER LIFT FOR REMOTE
  • MIL-STD 209K TRAILER TIE-DOWN AND LIFTING LUGS
  • COMPREHENSIVE OPERATIONS MANUAL PLUS WARRANTY
  • 24 HOUR SUPPORT
  • OVERSEAS SHIPMENTS UNITS ARE COMPLETELY SPRAYED COATED
  • HIGH WIND ALL TERRAIN OFF-ROAD APPLICATIONS
  • CAN BE PULLED WITH STANDARD 3/4 TON PICKUP TRUCK FOR OFF ROAD 4X4 RECOMMENDED
  • BUILT FOR ROUGH / INACCESSIBLE TERRAIN APPLICATIONS
  • CAN BE PULLED IN WITH BULLDOZERS, AND DEPLOYED MILITARY DESIGNED TO MEET MOST MILITARY ENVIRONMENTAL AND TRANSPORT APPLICATIONS
  • ENGINEERED AND DESIGNED TO MEET THE RIGOR DEMANDS
  • TIRES AND WHEELS CAN BE REMOVED FOR PERMANENT INSTALLATION OR FOR PREVENTION OF THEFT, VANDALISM OR LONG TERM.  WITH MID-LEVEL OUTRIGGER AND REAR JACKS IN PLACE.

A FEW OPTIONS

  • LOCKOUT KIT, FOR CLIMBER SAFETY
  • SAFETY CLIMB, FOR CLIMBER SAFETY
  • LIGHTNING PROTECTION
  • FAA LIGHTING
  • EXTRA REELS
  • SLIDE OUT
  • SAFETY RAILS
  • PAN ADAPTER
  • STARR MOUNT
  • GROUNDING KIT
  • TOWER COVERS
  • GENERATORS
  • FUEL TANKS
  • FUEL PUMPS
  • LIGHTING PROTECTION KIT

LMS 202 CR WEIGHTS AND DIMENSIONS

  • 7′ 2″ TALL
  • 7′ 7″ WIDE
  • 38′ RETRACTED HEIGHT, MINIMAL OPERATING HEIGHT
  • 39’10” TOTAL UNIT LENGTH
  • 39′ 3″ LENGTH WITHOUT HITCH
  • 30′ X 7’7″ DECK SURFACE
  • 16,500 Lbs EMPTY WEIGHT
  • 24,000 Lbs  GVWR
  • 7500 Lbs USE-FULL LOAD

DEPLOYED FOOTPRINT OF OUTRIGGERS

  • 17′ 3″ WIDE OUTRIGGERS EXTENDED
  • 51′ 7″ LONG OUTRIGGERS EXTENDED

PAINT OPTIONS/ CHOICE OF COLOR

  1. POLYURETHANE
  2. COMPLETE TRAILER PRIMED WITH INORGANIC ZINC CONFORMING TO MDDOD-P-23236A, COATED WITH AN EPOXY POLY-AMIDE INTERMEDIATE COAT CONFORMING TO MS MILL-P 2441 FORMULA 150 AND URETHANE TOP COAT CONFORMING L-P- TO MS MILL-C-85285. ALL TOWER ASSEMBLY HARDWARE IS GALVANIZED OR ECO HCF GREEN COATED FOR STAND-ALONE CORROSION RESISTANCE.

LMS 202 CR PRODUCT DESCRIPTION 2018-WORK

Certified Green Gin Poles are manufactured 100% from USA recycled steel. 

CERTIFIED SDVOSB | MANUFACTURING PLANT HUB ZONE | MINORITY OWNED COMPANY |  NATE MEMBER | SBA CERTIFIED SMALL DISADVANTAGED BUSINESS

Facility AWS D1.1 Certified, and 100% US Certified Welders welding to AWS, Certified 100% (AWS) D1.1 independent contractor inspected before leaving our facility. Towers are 100% hot dipped galvanized finished to EN ISO 1461/ASTM A123/CSA G164 and ANSI/EIA-TIA-222 G, per section 107 and CSA S37 standards. Steel is ASTM A500, grade B/C.  All products manufactured are Engineered and warranted. We have become the finest manufacturer of Gin Poles, Portable Towers, Climber Training Towers, Oil and Gas Flare Towers and Portable Shelters  in the Americas, thanks to team efforts and most important our customer support. “Service disabled veteran owned company built in America by Americans.” Minority owner and plant located in HUB zone.  Support our efforts as we support your freedom.

Landa Mobile Systems LLC supports and is in compliance affirmative action obligations on behalf of minorities, women, protected veterans and individuals with disabilities. Landa Mobile Systems, LLC complies fully with Executive Order 11246 and the applicable regulations of 41 CFR Part 60-1,-2; Section 503 of the Rehabilitation Act and the applicable regulations contained in 41 C.F.R. 60-741; as well as the Vietnam Era Veterans’ Readjustment Assistance Act and the applicable regulations contained in 41 C.F.R. 60-300.

image006      Nate-logo-large